Key words skeletal-axial - extremities - digital radiography - technology assessment
Introduction
For the first time worldwide, the multidimensional X-ray whole body imaging system
EOS (EOS Imaging, Paris, France) allows simultaneous acquisition of overview images
of several related body regions in 2 perpendicular planes [1 ]
[2 ]
[3 ]. The system consists of a 2.7 meter tall housing in which 2 CT X-ray tubes are arranged
perpendicular to one another. The height, speed and collimation are coordinated between
the two sources and move across the body region to be imaged while continuously releasing
X-radiation. The X-rays emitted by the patient are registered by 2 perpendicularly
arranged xenon gas detectors synchronized with both CT X-ray tubes. The particle detector
system is based on the principle of charge multiplication in gas under high pressure;
the result is electronic multiplication of the signals emitted by the examination
volumes [1 ]
[2 ]
[3 ]. The intensity of the scattered radiation sensed by this linear detector is reduced
by a slot diaphragm in order to improve the signal-to-noise ratio at the detector
input. According to the literature, increasing the amplitude of the measured signal
permits a reduction of the exposure dose compared to digital flat panel detector and
storage phosphor systems [1 ]
[2 ]
[3 ].
This instrument technology does not meet all the technical requirements listed in
the Expert and Examination Guidelines (SV-RL) for operating medical X-ray devices
[4 ]. This essentially refers to the requirements for a spatial high contrast resolution
capacity of at least 2.4 lp/mm, automatic exposure control and use of a special filter
for images of the trunk of children 12 years of age and under. Due to the specified
detector element pixel size of 250 µm, the high-contrast resolution of the EOS system,
when a system dosage is set corresponding to 400 FFS, is 2.0 lp/mm instead of the
required 2.4 lp/mm. Automatic exposure controls used for flat-configured radiography
systems (flat panel detectors, storage phosphors) using the principle of dosing via
a measuring chamber attached to the image receptor cannot be implemented when line
scanners such as the EOS system are used [5 ]. It is generally accepted that such X-ray equipment can be operated using preprogrammed
settings.
Although the EOS technology offers intrinsic advantages of exact 3-dimensional measurement
of joint angles and relatively low exposure dose, there are disadvantages including
the relatively low spatial resolution of the detector, lack of automatic exposure
control, the inability to acquire images of entire spinal columns occasionally required
in specialty clinics. In addition, high investment and operating costs also pose a
disadvantage [2 ]
[6 ]. In order to increase the cost-benefit ratio, utilization of EOS technology in morphological
skeletal and joint diagnosis has been discussed. For this reason, the Cologne district
government, as the competent nuclear supervisory authority, at the request of the
Ministry of Labor, Integration and Social Affairs of North Rhine Westphalia issued
an opinion to clarify whether the requirements of SV-RL regarding image quality and
general equipment of the EOS system would be equivalently fulfilled so that the prerequisites
under Paragraph 3, Sentence 2, no. 5 and Sentence 3 no. 2a and b of the X-ray Ordinance
would be met [5 ]. Within the scope of the evaluation, the imaging precision of the EOS system was
compared to a flat panel detector system (Digital Diagnost, Philips Healthcare) using
measurements with the contrast-detail phantom (CDRAD type 2.0, Artinis). The results
of in vitro measurements indicated similar imaging quality of both examination methods.
An evaluation of the diagnostic image quality was not the subject matter of the assessment.
Based on this study, at the request of the state and district government, the diagnostic
image quality of the EOS technology should be compared with that of digital flat technology
as the reference standard. The project sought to concretely answer whether in retrospect
a sagittal flat panel detector image might be dispensed in favor of an EOS image in
the case of patients, in whom a full-leg examination was performed to diagnose synchronous
or metachronous position relationships, a pelvic image or X-ray examination had been
performed without any intervening change in findings.
Materials and Methods
Examination Technologies
The EOS X-ray stereotactic whole body imaging system produced by EOS Imaging, Paris,
France, had been on loan in the Orthopedic Radiology department of the Radiological
Institute since 09/2010. From 09/2010 to 02/2011 the data acquisition and image reconstruction
algorithm implemented in the system was optimized with the support of the manufacturer.
Since the signal-to-noise ratio of 2 D documentation in the area of the trunk when
the exposure parameters implemented by the vendor did not provide sufficiently reliable
detection of anatomical landmarks during automatic angle determination, the specified
exposure parameters were raised with the help of the manufacturer. By mutual agreement,
the originally specified values were individually adapted from 80 kV up to 95 kV and
200 mAs up to 320 mAs for normal weight and obese patients in order achieve optimum
image quality in relation to radiation exposure. Likewise, supported by the manufacturer,
the image calculation algorithms of the EOS system were optimized and adapted to the
image characteristics of the flat panel detector systems. Since 04/2011, a special
imaging calculation algorithm was available for previously acquired image data sets.
This product of EOS Imaging was designed to minimize elimination artifacts at the
borders of endoprotheses.
Creation of the overview images used the following equipment: 2 digital flat panel
detector work stations (Digital Diagnost, Philips Healthcare) with a scintillator
layer of cesium iodide, a usable detector surface of 43 × 43 cm, a 3000 × 3000 pixel
matrix, pixel size with a 0.143 mm edge length, 14-bit gray value depth and a nominal
DQE (Detective Quantum Efficiency) of 65 %.
Patients
During the period 03/01/2011 to 10/31/2011, all 214 patients of the Orthopedic University
Clinic were prospectively identified; these patients had undergone a whole leg examination
in the course of their medical care. In the related evaluation of image quality, those
whole leg examinations were included in which X-ray examinations of the pelvis or
knee were performed in the course of medical care within a maximum interval of 3 months
without changes of the clinical-radiological findings in the meantime. In the case
of patients with whole leg examinations and/or flat panel detector images meeting
inclusion criteria, the chronologically initial examination was selected for assessment.
If radiographic images of both knee joints taken at the same time were available,
then alternately the right and left side from patient to patient were included in
the evaluation in order to avoid giving excess weighting to the aspect ratios of an
individual patient, and thereby influencing the results.
Between 09/2011 and 11/2011, two members of the working group (B. K., C. W.), using
the SterEOS® console prepared comparison image sections of the pelvis or knee relative to the
framing of the flat panel detector. These images were based on the electronic records
of sagittal full leg images of each patient. Oblique or lateral images were rejected
in both of the two technologies, since in the pelvis and hip joint region there were
no lateral flat panel detector images, and since lateral EOS images of the knee joint
were generally negatively affected by overlapping of the contralateral knee. In addition,
the EOS and flat panel detector images were pseudonymized and assigned random numbers
when stored in the SterEOS® image processing console.
Image Evaluation Process
Starting in 04/2012 the EOS and flat panel detector images were evaluated in random
order by 4 radiologists (B. K., N.-M. S., H. S., B. W.) using an electronic data collection
form while working independently using the SterEOS® work station. The form was employed to sample the image quality of normal anatomical
structures and neocorticals along the metal implants using a 6-stage assessment scale
from 1: “anatomical structure well-delineated in all sections” to 6: “anatomical structure
not delineated”. During the assessment it was not revealed whether the image sources
were from were EOS or flat panel detectors. A time interval of at least 4 months was
established between the preparation of the images and the start of the evaluation
in order to prevent the assessors from remembering the image pair correlations. Three
assessors were specialist physicians in radiology (B. K., H. S., B. W.); one assessor
was in third year medical residency as a radiologist (N.-M. S.). Two assessors (B. K.,
B. W.) possessed long years of experience in evaluating digital projection radiography.
Statistical Evaluation
The assessors’ notations were recorded in an IT-supported dialog using Excel (Microsoft
Corp., Redmond, WA, USA). Statistical analysis were performed using SPSS Statistics
(IBM Corp., Armonk, NY, USA).
The patient-related pairings of EOS and flat panel detector images formed the basis
for the statistical evaluation. Following this were the paired comparisons of various
related anatomical regions: right/left os ileum and upper os sacrum, relating to the
large pelvis region; likewise compared were right/left acetabulum, right/left os pubis,
right femoral head, right femoral neck, right greater trochanter, right proximal femoral
diaphysis; left femoral head, left femoral neck, left greater trochanter and left
proximal femoral diaphysis relating to the small pelvis/hip. Likewise considered were
the paired comparisons of the anatomical regions distal femoral diaphysis, condylus
medialis, basis patellae, intercondylar eminence, tibial metaphysis, and proximal
fibula relating to the general knee region. The notations of every assessor for each
collective region were collected and presented as indications of mean values, standard
deviations, minimum and maximum as well as box and whiskers plots in the general overview
and for secondary issues.
Results
Key Patient and Examination Data
Between 03/01/2011 and 10/31/2011, the EOS system was initially used for whole-leg
examinations of 114 patients for whom there were no clinical-radiological changes
over a maximum of 3 months determined by findings based on overview images using a
flat panel detector system. Of these, 62 patients underwent pelvic imaging (54.4 %)
and 55 patients (48.2 %) had knee joint imaging. Three patients (2.6 %) fulfilled
the inclusion criteria for pelvic overview imaging as well as X-ray imaging of the
knee joint. The time interval between both examinations was on average 6.7 days ± 14.4
days standard deviation (minimum 0 days, maximum 73 days). Of the 114 patients, 64
were female (56.1 %) and 50 were male (43.9 %). The mean age was 63.7 years ± 15.0
years standard deviation; the minimum was 20 years, maximum 93 years of age. The cohort
included exclusively patients of the Orthopedic University Clinic who had been referred
to the radiologist due to clinical complaints, for planning replacement of hip or
knee joints, as well as patients referred for postoperative checkups ([Table 1 ]).
Tab. 1
Clinical data.
Characteristic
Number of patients (n)
Number of patients (%)
patients
114
100
female patients
64 of 114
56.1
male patients
50 of 114
43.9
indications
pelvis overview images
62
100
clinical symptoms
17 of 62
27.4
planning a hip TEP
22 of 62
35.4
control after a current implantation of a hip TEP
12 of 62
19.4
symptoms after an old implantation of a hip TEP
11 of 62
17.8
knee overview images
55
100
clinical symptoms
16 of 55
29,
.1
planning a knee TEP
17 of 55
30.9
control after a current implantation of a hip TEP
17 of 55
30.9
symptoms after an old implantation of a hip TEP
5 of 55
9.1
TEP = Total prosthetic replacement
The sagittal whole leg images were ranked by body weight produced using the following
preset values: one patient with presets of 80 kV and 200 mAs; 15 patients with 85 kV
and 200 mAs; 2 patients with 85 kV and 250 mAs; 5 patients with 95 kV and 250 mAS;
54 patients with 95 kV and 320 mAs; one patient with 100 kV and 400 mAs; 5 patients
with 104 kV and 320 mAs; 30 patients with 104 kV and 400 mAs, as well as one patient
with 125 kV and 320 mAs. The mean dose area product for all sagittal whole leg images
was 12.5 cGyc × cm2 ± 4.1 cGyc × cm2 (minimum 4.5 cGyc × cm2 , maximum 19.6 cGyc × cm2 ) ([Table 2 ]).
Tab. 2
Dose area product
dose area product (cGy*cm2 )
type of image
number of patients (N)
mean
standard deviation
minimum
maximum
whole leg images
114
12.5
4.1
4.5
19.6
pelvis overview images
62
17.6
11
3.8
56.6
knee overview images
55
2.2
1.2
0.3
6.8
62 sagittal examinations were prepared with 77 kV (59 examinations) or 81 kV (3 examinations).
On average the charge was 19.01 mAs ± 11.34 mAs (4.00 mAs, maximum 67.00 mAs) and
the dose area product was 17.6 cGyc × cm2 ± 11.0 cGyc × cm2 (minimum 3.8 cGyc × cm2 , maximum 56.6 cGyc × cm2 ) ([Table 2 ]). The same values applied to the 55 sagittal examination of the knee: 66 kV (54
examinations) and 70 kV (1 examination) as well as 7.62 mAs ± 3.89 mAs (24.30 mAs,
maximum 2.30 mAs), corresponding to a dose area product of 2.2 cGyc × cm2 ± 1.2 cGyc × cm2 (minimum 0.3 cGyc × cm2 , maximum 6.8 cGyc × cm2 ).
Image Evaluations
[Fig. 1 ] illustrates the ranking for each assessor according to the anatomical regions “large
pelvis”, “small pelvis/hip” and “knee”. Assessment used a direct “flat panel detector
image” vs. “EOS image” comparison in the form of a box and whispers plot. The image
quality of the EOS images was graded inferior to that produced by flat panel detectors;
this assessment was unrelated to the assessors’ level of training or familiarity with
EOS technology ([Fig. 2 ], [3 ]). This applies both to the delineation of corticals and spongiosa structure as well
as the neocortical boundary lamella in the case of osteosynthetic implants. The results
were not dependent on the thickness of the X-rayed body region.
Fig. 1 Box-whiskers plots of the four readers’ assessments based on matched pair comparisons.
The upper and lower borders of the squares indicate the upper and lower simple standard
deviation; the horizontal lines within the squares show the mean values; the broken
lines represent the upper and lower double standard deviation; and the circle and
star symbols indicate the statistical outliers. The assessments relating to the numbers
on the left were: “1 = Criterion in all sections well-delineated”; “2 = Majority of
sections well-delineated”; “3 Majority of sections satisfactorily delineated”; “4 = Majority
sufficiently delineated”; “5 = Insufficiently delineated”; and “6 = Not delineated”.
The differing numbers of matched image comparisons per assessor is because in individual
cases, the anatomical region was classified by the assessor as not shown, so a paired
comparison was not possible. Upper row: superior region “large pelvis” including the
individual regions right os leum, left os ileum, upper os sacrum. For assessors 1
to 3 there were 61, 62 and 60 pairs respectively for the criteria “delineation of
cortical bone” and “delineation of spongiosa”. For the criterion “delineation of neocortical
boundary lamella for osteosynthesis material” there were, respectively, 4, 1 and 3
matched images. Assessor 4 evaluated 6 image pairs for the first two criteria and
none for the third. Center row: superior region “small pelvis/hip” includes evaluation
of the following individual regions: right/left acetabulum, right/left os pubis, right
femoral head, right femoral neck, right greater trochanter, right proximal femoral
diaphysis; left femoral head, left femoral neck, left greater trochanter and left
proximal femoral diaphysis. For assessors 1 to 3 there were 62, 62 and 61 pairs respectively
for the criteria “delineation of cortical bone and spongiosa” and “delineation of
neocortical boundary lamella” there were, respectively, 44, 43 and 41 matched images.
Assessor 4 evaluated 6 image pairs with respect to the first two criteria and 5 with
respect to the third. Lower row: superior region “knee” includes evaluation of the
following individual regions: distal femoral diaphysis, condylus medialis, basis patellae,
eminentia intercondylaris, proximal tibial metaphysis and proximal fibula. For the
first two criteria, assessors 1 to 4 had access to 55, 54, 54 and 4 image pairs respectively;
for evaluation of the last criteria they had 35, 35, 37 and 2 image pairs respectively.
Fig. 2 Matched pair comparisons with the largest differences of the mean assessments of
the visualization of the spongiosa of reader 1 in favour of the flat-panel technology.
a superior region “pelvis/hip”. Flat-panel images. Mean assessments of the region “large
pelvis”: Reader 1: 1.3, reader 2: 3.3 and reader 3: 1.0 as well as region “small pelvis/hip”:
Reader 1: 1.1, reader 2: 2.6 and reader 3: 1.3. b superior region “pelvis/hip”. EOS-images. Mean assessments of the region “large pelvis”:
Reader 1: 5.0, reader 2: 5.5 and reader 3: 3.7 as well as superior region “small pelvis/hip”:
Reader 1: 3.6, reader 2: 4.5 and reader 3: 2.8. c superior region “knee”. Flat-panel images. Mean assessments of reader 1: 1.2, of reader
2: 2.0 and of reader 3: 1.6. d superior region “knee”. EOS-images. Mean assessments of reader 1: 4.2, of reader
2: 4.4 and of reader 3: 4.0.
Fig. 3 Matched pair comparisons with the largest differences of the mean assessments of
the visualization of the spongiosa of reader 1 in favour of the EOS-technology. a superior region “pelvis/hip”. Flat-panel images. Mean assessments of the region „large
pelvis“: Reader 1: 3.3, Reader 2: 3.0 and reader 3: 1.0 as well as of the region “small
pelvis/hip”: Reader 1: 1.7, reader 2: 2.4 and reader 3: 1.1. b superior region „pelvis/hip“. EOS-images. Mean assessments of the region “large pelvis“:
Reader 1: 3.0, reader 2: 4.03 and reader 3: 2, as well as of the region ”small pelvis/hip“:
Reader 1: 3.0, reader 2: 3.4 and reader 3: 1.6. c superior region “knee”. Flat-panel images. Mean assessments of reader 1: 2.0, of reader
2: 2.7 and of reader 3: 1.3. d superior region “knee”. EOS-images. Mean assessments of reader 1: 1.5, of reader 2:
2.3 and of reader 3: 2.3.
In the general view of all assessors with respect to all examined skeletal regions,
flat panel detector technology produced 82.6 % ± 13.2 % qualitatively superior image
pairs, whereas 2.0 % ± 2.6 % of EOS images were ranked as superior ([Table 3 ]). Where 0.8 % ± 3.2 % of the flat panel detector images were graded “5” or “6”,
i. e. diagnostically insufficient, 29.9 % ± 33.9 % of the EOS images were considered
insufficient. In the overview of all assessors and of all skeletal regions a constellation
of the evaluation of flat panel detector images were considered diagnostically insufficient
(rated “5” or “6”), compared to a diagnostically good rating of corresponding EOS
images (rating “1” or “2”) was 0.1 ± 0.4 %. Conversely, 29.9 ± 32.9 % of the EOS image
pairs were rated diagnostically insufficient (rated “5” and “6”) compared to a flat
panel detector images rated as diagnostically good (rated “1” or “2”). The extent
of the results was continually confirmed by the individual assessors with respect
to examined regions ([Table 3 ]).
Tab. 3
Overview of the assessments of the superior anatomical regions “large pelvis”, “small
pelvis/hip” and “knee” of each assessor for the higher-level anatomical regions as
well as the summary of all anatomical regions and all assessors.
assessor
region
evaluation criterion
number of assessed individual regions (n)
mean
standard deviation
minimum
maximum
1
large pelvis
number of images (n)
3
60
1
59
61
superior FD image (%)
3
85.0
5.7
78.7
89.8
insufficient FD image (%)
3
0.0
0.0
0.0
0.0
insufficient FD image, EOS image good (%)
3
0.0
0.0
0.0
0.0
superior EOS image (%)
3
2.2
0.9
1.7
3.3
insufficient EOS image (%)
3
33.5
3.3
31.1
37.3
insufficient EOS image, FD image good (%)
3
33.5
3.3
31.1
37.3
small pelvis/hip
number of images (n)
12
51
13
29
62
superior FD image (%)
12
94.1
3.0
89.8
98.3
insufficient FD image (%)
12
0.0
0.0
0.0
0.0
insufficient FD image, EOS image good (%)
12
0.0
0.0
0.0
0.0
superior EOS image (%)
12
0.3
0.6
0.0
1.6
insufficient EOS image (%)
12
22.3
9.5
8.5
37.9
insufficient EOS image, FD image good (%)
12
22.3
9.5
8.5
37.9
knee
number of images (n)
6
51
7
37
55
superior FD image (%)
6
81.5
9.2
63.6
89.1
insufficient EOS image (%)
6
0.0
0.0
0.0
0.0
insufficient FD image, EOS image good (%)
6
0.0
0.0
0.0
0.0
superior EOS image (%)
6
3.7
3.2
0.0
9.1
insufficient EOS image (%)
6
1.4
1.1
0.0
2.7
insufficient EOS image, FD image good (%)
6
1.4
1.1
0.0
2.7
2
large pelvis/hip
number of images (n)
3
61
2
59
62
superior FD image (%)
3
70.0
2.6
67.7
72.9
insufficient EOS image (%)
3
2.3
3.9
0.0
6.8
insufficient FD image, EOS image good (%)
3
0.6
1.0
0.0
1.7
superior EOS image (%)
3
8.2
1.9
6.5
10.2
insufficient EOS image (%)
3
23.3
16.6
12.9
42.4
insufficient EOS image, FD image good (%)
3
21.6
13.6
12.9
37.3
small pelvis/hip
number of images (n)
12
52
13
29
62
superior FD image (%)
12
74.2
4.5
68.3
83.6
insufficient flat detector image (%)
12
0.0
0.0
0.0
0.0
insufficient FD image, EOS image good (%)
12
0.0
0.0
0.0
0.0
superior EOS image (%)
12
2.9
1.6
0.0
5.7
insufficient EOS image (%)
12
11.3
9.1
0.0
25.7
insufficient EOS image, FD image good (%)
12
11.3
9.1
0.0
25.7
knee
number of images (n)
6
51
7
37
54
superior FD image (%)
6
62.4
8.1
48.1
70.4
insufficient flat detector image (%)
6
0.9
1.0
0.0
1.9
insufficient FD image, EOS image good (%)
6
0.3
0.8
0.0
1.9
superior EOS image (%)
6
6.8
1.9
3.7
9.3
insufficient EOS image (%)
6
7.1
5.5
0.0
11.3
insufficient EOS image, FD image good (%)
6
6.5
5.2
0.0
11.1
3
large pelvis
number of images (n)
3
59
1
58
59
superior FD image (%)
3
88.1
2.9
86.4
91.4
insufficient flat detector image (%)
3
1.1
1.0
0.0
1.7
insufficient FD image, EOS image good (%)
3
1.1
1.0
0.0
1.7
superior EOS image (%)
3
3.4
0.0
3.4
3.4
insufficient EOS image (%)
3
17.7
5.7
13.6
24.1
insufficient EOS image, FD image good (%)
3
17.7
5.7
13.6
24.1
small pelvis/hip
number of images (n)
12
48
13
26
61
superior FD image (%)
12
71.9
6.2
63.3
79.7
insufficient flat detector image (%)
12
0.0
0.0
0.0
0.0
insufficient FD image, EOS image good (%)
12
0.0
0.0
0.0
0.0
superior EOS image (%)
12
1.0
1.1
0.0
3.3
insufficient EOS image (%)
12
6.6
3.9
0.0
11.8
insufficient EOS image, FD image good (%)
12
6.6
3.9
0.0
11.8
knee
number of images (n)
6
51
7
37
54
superior FD image (%)
6
73.2
8.8
63.0
87.0
insufficient flat detector image (%)
6
0.6
1.0
0.0
1.9
insufficient FD image, EOS image good (%)
6
0.3
0.8
0.0
1.9
superior EOS image (%)
6
1.9
1.7
0.0
3.7
insufficient EOS image (%)
6
2.1
2.1
0.0
5.4
insufficient EOS image, FD image good (%)
6
1.8
2.0
0.0
5.4
4
large pelvis
number of images (n)
3
6
1
5
6
superior FD image (%)
3
94.4
9.6
83.3
100.0
insufficient flat detector image (%)
3
11.1
9.6
0.0
16.7
insufficient FD image, EOS image good (%)
3
0.0
0.0
0.0
0.0
superior EOS image (%)
3
0.0
0.0
0.0
0.0
insufficient EOS image (%)
3
100.0
0.0
100.0
100.0
insufficient EOS image, FD image good (%)
3
88.9
9.6
83.3
100.0
small pelvis/hip
number of images (n)
12
5
1
2
6
superior FD image (%)
12
97.2
6.5
83.3
100.0
insufficient flat detector image (%)
12
1.4
4.8
0.0
16.7
insufficient FD image, EOS image good (%)
12
0.0
0.0
0.0
0.0
superior EOS image (%)
12
0.0
0.0
0.0
0.0
insufficient EOS image (%)
12
82.6
21.5
33.3
100.0
insufficient EOS image, FD image good (%)
12
81.3
21.9
33.3
100.0
knee
number of images (n)
6
4
1
2
4
superior FD image (%)
6
95.8
10.2
75.0
100.0
insufficient flat detector image (%)
6
0.0
0.0
0.0
0.0
insufficient FD image, EOS image good (%)
6
0.0
0.0
0.0
0.0
superior EOS image (%)
6
0.0
0.0
0.0
0.0
insufficient EOS image (%)
6
75.0
22.4
50.0
100.0
insufficient EOS image, FD image good (%)
6
75.0
22.4
50.0
100.0
all asssessors
large pelvis
number of images (n)
12
46
25
5
62
superior FD image (%)
12
84.4
10.7
67.7
100.0
insufficient flat detector image (%)
12
3.6
6.4
0.0
16.7
insufficient FD image, EOS image good (%)
12
0.4
0.8
0.0
1.7
superior EOS image (%)
12
3.5
3.3
0.0
10.2
insufficient EOS image (%)
12
43.6
35.3
12.9
100.0
insufficient EOS image, FD image good (%)
12
40.4
30.8
12.9
100.0
small pelvis/hip
number of images (n)
48
39
23
2
62
superior FD image (%)
48
84.3
12.6
63.3
100.0
insufficient flat detector image (%)
48
0.3
2.4
0.0
16.7
insufficient FD image, EOS image good (%)
48
0.0
0.0
0.0
0.0
superior EOS image (%)
48
1.0
1.5
0.0
5.7
insufficient EOS image (%)
48
30.7
33.2
0.0
100.0
insufficient EOS image, FD image good (%)
48
30.4
32.7
0.0
100.0
knee
number of images (n)
24
39
22
2
55
superior FD image (%)
24
78.2
15.1
48.1
100.0
insufficient flat detector image (%)
24
0.4
0.8
0.0
1.9
insufficient FD image, EOS image good (%)
24
0.2
0.5
0.0
1.9
superior EOS image (%)
24
3.1
3.2
0.0
9.3
insufficient EOS image (%)
24
21.4
33.5
0.0
100.0
insufficient EOS image, FD image good (%)
24
21.2
33.6
0.0
100.0
total
number of images (n)
84
40
23
2
62
superior FD image (%)
84
82.6
13.2
48.1
100.0
insufficient flat detector image (%)
84
0.8
3.2
0.0
16.7
insufficient FD image, EOS image good (%)
84
0.1
0.4
0.0
1.9
superior EOS image (%)
84
2.0
2.6
0.0
10.2
insufficient EOS image (%)
84
29.9
33.9
0.0
100.0
insufficient EOS image, FD image good (%)
84
29.2
32.9
0.0
100.0
FD = Flat Detector.
Discussion
Compared to similar technologies on the market, the EOS X-ray stereotactic whole body
imaging system (EIS Imaging, Paris, France) offers the unique selling proposition
of providing simultaneous radiographical projections of the entire body or larger
body sections in 2 perpendicularly arranged planes. The two image data sets enable
the generation of 2-dimensional representations of the examined body region; based
on this, the precise angle of complex skeletal structures can be determined in all
three planes of the patient’s upright position [7 ]
[8 ]
[9 ]
[10 ]
[11 ]
[12 ]. An electronic image fusion of several individual exposures for the generation of
full spine and full leg images as in conventional digital imaging systems is eliminated.
Special processing algorithms allow semi-automatic generation of a pseudo-3 D representation
of the examined body regions from the biplanar electronic image data sets [1 ]
[2 ]
[3 ]. Here image reconstruction is based on standard data sets of skeletal structures
obtained from larger patient cohorts. In the pseudo-3 D images, the lengths and angles
of the skeletal section are properly reproduced. However, due to the projected nature
of both overview images supporting 3 D imaging, the three-dimensional representation
of the skeleton is only virtual. Numerous in vivo and in vitro studies have discussed
the accuracy of such angle determinations and their medical utility [7 ]
[8 ]
[10 ]
[11 ]
[12 ]
[13 ]
[14 ].
Since the indications justifying exact three-dimensional radiological determination
of skeletal angle in the patient population of an orthopedic specialty clinic compared
to conventional skeletal diagnostics are likely to be relatively rare, an X-ray stereotactic
system used only for angle and position determination will generally not be fully
utilized in the course of daily activities [2 ]
[15 ]. Dietrich et al. compared the processes of EOS technology with the characteristics
of standard digital technology (Ysio, Siemens Healthcare) for the generation of 133
whole spine images and 185 whole leg images [15 ]. According to Dietrich et al. the financial break-even point for Swiss economic
circumstances was 4 X-ray stereotactic examinations per work day instead of 3 whole
spine examinations performed per work day using the standard system [15 ]. An increase in utilization frequency and improvement of the operating costs of
EOS technology could be achieved if the system could also be used for position verification
in morphological skeletal diagnostics.
On the other hand, detector technology with a nominal spatial resolution of 2.0 lp/mm
in the high-contrast range does not meet the requirements of the Expert and Examination
Guidelines (SV-RL) [4 ]. The hypothesis, that high contrast dynamics offset the low spatial resolution,
was reviewed analogously to the procedure in digital mammography using in vitro measurements
with the contrast detail phantom CDRAD type 2.0 made by Artinis [5 ]. Similar to the CDMAM phantom in digital mammography, the CDRAD phantom is used
for simultaneous comparison of X-ray systems with respect to their contrast and spatial
resolution (contrast resolution capability) [5 ]
[16 ]
[17 ]
[18 ]
[19 ]
[20 ]. The phantom consists of a Plexiglas tablet with 225 squares, arranged in 15 rows
and columns with 1 or 2 cylindrical holes. The squares of the first 3 rows each exhibit
only one hole. The squares of rows 4 through 15 each have 2 identical holes, whereby
one hole lies in the center of the square, and one is located in one of the four corners
of the square. Within a row, the depth of the hole increases exponentially while the
diameter remains constant (test of contrast resolution). The same applies to diameter
within a column while the hole depth remains constant (test of spatial resolution).
Using the EOS system, a flat panel detector system (Digital Diagnost, Philips Healthcare),
and a digital storage phosphor system (Optimus DR, Philips Healthcare), 9 overview
images of the phantom were taken with each system, using comparable imaging parameters
(15 cm thick PMMA – polymethyl methacrylate attenuation element). The flat panel detector
and storage phosphor systems used automatic exposure control, focus image receptor
distance, 110 cm, focal spot size 1.0 × 1.0. The EOS system used focus image receptor
distance, 130 cm, focal spot size 0.6 × 1.3. The EOS images were acquired using manual
selection of the exposure parameters, so that in a first measurement series the appropriate
incident dose was determined to correspond to the flat panel detector system. In a
second measurement series, the manufacturer’s recommended exposure parameters were
used for examination of the lower spinal column. Each exposure was evaluated by three
assessors working independently. The indicated positions of the holes were compared
with their actual locations. As a result, the contrast resolution capability of the
EOS system corresponded to that of the flat panel detector system at the same incident
dose. In the case of examinations performed with the manufacturer’s recommended exposure
parameters, the contrast resolution capability of the EOS system lay between that
of the flat panel detector and the storage phosphor system.
The comparable image quality of EOS technology and that of digital flat panel detector
radiography described in the phantom tests was not confirmed in clinical application.
Instead, the flat panel detector images were rated qualitatively superior to EOS images
by a mean 83 % with ± 13 % standard deviation. Of the EOS images, 30 % ± 34 % were
considered diagnostically insufficient.
The discrepancy between the results of the phantom study and actual patient examinations
is explained by the fact that phantom studies can only reproduce a simplified simulation
of multidimensional biological reality. The 15 cm-wide PMMA scattering body used in
the in vitro measurements insufficiently represented the absorption conditions of
the human trunk and lower extremities of the largely obese patients involved in the
clinical study. The fact that the extent of the obesity of the patients could not
be retrospectively determined represents a methodical limitation of the study. Although
during phantom measurements sufficient X-ray quanta for adequate image generation
arrived at the detector, the relation in the clinical studies between the level of
exposure dose, radiation absorption, and scattering within the irradiated body volume
and the signal registration at the detector was unfavorable in a clinically-relevant
number of patients; consequently the low spatial resolution could not be offset by
the high contrast dynamics of the image reception system. In order to increase the
signal level registered in the detector input for the generally obese patients in
these clinical studies, and thus improve the signal-to-noise level, adaptations to
the sagittal whole leg images were performed in conjunction with the manufacturer.
These included multiple increases in tube voltage from 95 kV to 125 kV instead of
77 kV to 81 kV for pelvis overview examinations, and 66 kV to 70 kV for knee joints.
Adjustment of the exposure parameters prior to the start of the study phase resulted
in a reduction of background noise; as a consequence, this resulted in a reduction
of detail contrast. In order to avoid exposing the patient to an excessively high
organ dose in the course of treatment, an increase compared to the initial implementation
of a constant kV rate (80 kV to 95 kV, depending on the patient’s body size), from
200 mAs or 320 mAs to the maximum possible value of 400 mAs was not used. In comparison,
81 kV was used in phantom measurements for both the X-ray stereotactic images as well
as for the flat panel detector and storage phosphor radiographs. Some exceptions to
this were EOS images which, according to the manufacturer’s recommendation, were produced
using a 95 kV tube voltage.
To the best of the authors’ knowledge, to-date there are no publications regarding
the qualitative comparison of X-ray stereotactic images of entire spines or legs or
the diagnostic evaluation of the flat panel detector images of cortical and spongiosa
structure. Deschenes et al. compared whole spine images of 50 scoliosis patients using
X-ray stereotactic images (EOS, EOS Imaging) and conventional, one-dimensional images
(Fuji FCR 7501S, Fuji) [21 ]. The delineation of anatomical landmarks relevant to angle measurement were evaluated
by 4 independent assessors using a four-level scale. To summarize, the quality of
the EOS images were rated superior to those of the whole spine images produced by
the Fuji system, despite the lower exposure dose. Due to the incomplete description
of the methodology and the results, there is some doubt regarding the clinical relevance
of the conclusions [2 ].
Compared to the corresponding values of Dietrich et al. which used a mean dose area
product of 9.2 cGyc × cm2 ± 4.6 cGyc × cm2 for 185 consecutive X-ray stereotactic whole leg images, the dose area product in
this study was somewhat higher, with 12.5 cGyc × cm2 ± 4.1 cGyc × cm2 for sagittal images [15 ]. The diagnostic image quality was not evaluated by Dietrich et al.
In summary, the EOS X-ray stereotactic imaging system, in the context of whole leg
imaging, can be employed only for position control. At this juncture, in its current
configuration, the system is not suitable for additional morphological skeletal diagnosis.
This could change as a result of progress in detector technology leading to greater
geometric detector resolution.
Central statements:
X-ray stereotactic whole leg images in two perpendicular planes are suitable for the
measurement of exact three-dimensional angles in complex skeletal regions of a patient
in upright position.
The quality of images acquired using currently available X-ray stereotactic technology,
when compared to standard digital flat panel detector radiography, is insufficient
for diagnostic assessment of cortical and spongiosa structures.
Despite equivalent results of reference measurements of a contrast detail phantom
(CDRAD type 2.0, Artinis), the X-ray stereotactic system was inferior to flat panel
detector technology used in routine clinical diagnostics in a university orthopedic
specialty clinic.
In the case of patients who in the course of medical care underwent full-leg examinations
for the diagnosis of synchronous or metachronous position relationships without an
intervening change in the findings or who had pelvic overview imaging, it can be stated
retrospectively that a flat panel detector image could not have been dispensed with
in favor of an EOS image.
