Informationen aus Orthodontie & Kieferorthopädie 2006; 38(1): 12-16
DOI: 10.1055/s-2006-921533
Originalarbeit

© Georg Thieme Verlag

Temperaturmessung bei der Entfernung von Composite nach Brackettabnahme

Temperature Measurement During Mechanical Removal of Composite Material After Bracket RemovalE. Jonke1 , F. Weiland2 , J. W. Freudenthaler1 , H.-P. Bantleon1
  • 1Abteilung für Kieferorthopädie, Univ.-Klinik für Zahn-, Mund- und Kieferheilkunde, Österreich
  • 2Privatpraxis Deutschlandsberg, Austria
Further Information

Publication History

Publication Date:
23 March 2006 (online)

Zusammenfassung

In einer In-vitro-Untersuchung wurde die Temperaturentwicklung bei der mechanischen Entfernung von Composite untersucht. Rotierende Instrumente aus Hartmetall mit unterschiedlicher Anzahl von Querwindungen wurden verwendet, um die Temperaturentwicklung bei der Entfernung von Compositematerial an frisch extrahierten Zähnen sowie auf Hydroxylapatitscheiben verschiedener Stärke zu messen. Bei der Verwendung von Schleifkörpern mit feinerer Oberfläche (40 Windungen; dabei zählten die Windungen des Bohrers über seine Längsachse) kam es lediglich zu einem Temperaturanstieg von 1,2 °C im Pulpenbereich, wohingegen Schleifkörper mit einer geringeren Anzahl von Windungen (6W) einen Temperaturanstieg von 9,4 °C (p < 0,001) bewirkten. Zwischen 3 und 8 Sekunden ist der Temperaturanstieg am größten. Daher wird intermittierendes Arbeiten, d. h. eine Pause nach ca. 5 Sekunden empfohlen.

Abstract

The temperature increase during mechanical removal of composite material was measured in an in-vitro test. Different carbide burs were studied while a high-speed hand piece was used. The burs showed a divergent surface design, i. e. the amount of windings measured to the long axis of the shaft differed from 6 to 40. The buccal surface of recently extracted front teeth and slices of hydroxyapatite were subject to testing. It could be shown that the most pronounced rise in temperature (9.4 °C, p < 0.001) was achieved with coarse burs whereas burs with multiple windings increased temperature by not more than 1.2 °C. As the maximum temperature is reached after 3 to 8 seconds, polishing should be done intermittently for not more than 5 seconds.

Literatur

  • 1 Bantleon H P, Petrin P, Droschl H. Kleberentfernung mittels rotierender Instrumente - eine licht- und rasterelektronische Untersuchung.  Z Stomatol. 1985;  82 95-105
  • 2 Behrens V G, Gutknecht N. Transmission and absorption of laser radiation as well as temperature transference through dental hard issues. 3rd International Congress on Lasers in Dentistry, Salt Lake City, Utah, August 6-8 1992; 191-192
  • 3 Behrens V G, Gutknecht N. Transmission and absorption of laser radiation as well as temperature transference through dental hard issues. 3rd International Congress on Lasers in Dentistry, Salt Lake City, Utah, August 6-8 1992; Abstract 105: 56
  • 4 Brown C RL, Way D C. Enamel loss during orthodontic bonding and subsequent loss during removal of filled and unfilled adhesives.  Am J Orthod. 1978;  74 663-671
  • 5 Cummings M, Biagioni P, Lamey P J, Burden D J. Thermal image analysis of electrothermal debonding of ceramic brackets: an in vitro study.  Eur J Orthod. 1999;  21 111-118
  • 6 Jonke E, Manschiebel W, Wernisch J, Bantleon H P. Vergleichende Untersuchung der Zahnoberflächenbeschaffenheit nach Bracketabnahme.  Inform Kieferorthop. 1999;  31 253-257
  • 7 Jost-Brinkmann P G, Stein H, Miethke R R, Nakata M. Histologic investigation of the human pulp after thermodebonding of metal and ceramic brackets.  Am J Orthod Dentofacial Orthop. 1992;  102 410-417
  • 8 Krell K V. Orthodontic bracket removal using conventional and ultrasonic debonding techniques, enamel loss, and time requirements.  Am J Orthod Dentofacials Orthodop. 1993;  103 258-266
  • 9 Lisanti V F, Zander H A. Thermal injury to normal dog teeth: in vivo measurements of pulp temperature increases and their effect on the pulp tissue.  J Dent Res. 1952;  31 548-558
  • 10 Nyborg H, Brannstörm M. Pulp reaction to heat.  J Prosthet Dent. 1968;  19 605-612
  • 11 Pohto M, Scheinin A. Microscopic observations on living dental pulp. Part 2.  Acta Odontol Scand. 1957;  24 303-314
  • 12 Reichrath A. Über die Temperaturentwicklung im Pulpenvakuum gesunder, excavierter und mit Füllungen versorgter Zähne beim Genuss warmer, heißer und extrem kalter Speisen - eine experimentelle Studie. Thesis. Johannes Gutenberg-Universität, Mainz 1983
  • 13 Retief D H, Denys F R. Finishing of enamel surfaces after debonding of orthodontic attachments.  Angle Orthod. 1979;  49 1-10
  • 14 Sheridian J J, Brawley G, Hastings J. Electrothermal debracketing. Part I. An in vitro study.  Am J Orthod. 1986;  89 21-27
  • 15 Tocchio R M, Williams P T, Mayer F J, Standing K G. Laser debonding of ceramic orthodontic brackets.  Am J Orthod Dentofacial Orthop. 1993;  103 155-162
  • 16 Vieira A C, Pinto R A, Chevitarese O, Almeida M A. Polishing after debracketing: its influence upon enamel surface.  J Clin Pediatr Dent. 1993;  18 7-11
  • 17 Vukovich M E, Wood D P, Daley T D. Heat generated by grinding during removal of ceramic brackets.  Am J Orthod Dentofacial Orthop. 1991;  99 505-512
  • 18 Zach L, Cohen G. Pulp response to externally applied heat.  Oral Surg Oral Med Oral. Path1965;  19 515-529
  • 19 Zarrinia K, Eid N M, Kehoe M J. The effect of different debonding techniques on the enamel surface: an in vitro qualitative study.  Am J Orthod Dentofacial Orthop. 1995;  108 284-293

1 Ormco Corp, Glendora, Calif

2 Ormco Corp, Glendora, Calif

3 Reliance Orthodontic Products, Itasca, Illinois

4 Light-Bond, Reliance Orthodontic Products, Inc; Itasca, USA

Prof. DDr. E. Jonke
Facharzt für Zahn-, Mund- und Kieferheilkunde · Kieferorthopädie

Mariahilfer Straße 32

1070 Wien

Österreich

Phone: +43/01/5 24 48 68

Fax: +43/01/5 24 48 68 68

Email: erwin.jonke@meduniwien.ac.at

    >